What are the matters needing attention in the operation of the switch
Release time：2019-09-16 Clicks： Click
How should the switch be operated and what matters needing attention? Today we will give you a detailed introduction. The specific details are described below.
The method and precautions for the operation of the switch, especially if the transverse pressure type is overloaded, the riveting part will be damaged, which is the cause of the breakage of the switch. Therefore, during installation and operation, please be careful not to impose a load weight higher than the overload weight. Please press the plunger to set the switch in the direction of vertical movement. Pressing only one side of the plunger, or the oblique orifice, may result in reduced durability. No strong repetitive operation is allowed. If the plunger has been pressed under further pressure, excessive load weight may lead to the deformation of the circular panel spring, which becomes the cause of poor action. According to different needs, there are waterproof type and common type, switch connecting two lines, providing on-off control for electrical appliances, remembering, etc. The switch has the advantages of small contact spacing, short travel, small press power and quick on-off. Its moving contact speed and transmission surface are widely used. Such as: audio and video products, digital products, remote control, communication products, household appliances, security products, toys, computer products, fitness products, medical equipment, Zero marker keys and so on.
Firstly, the pin base material is the pin base material, and the pin base material of the light touch switch is brass or phosphorus copper (low grade is iron). In order to reduce the contact resistance, most of the pins are silver plated. SO2 gas in the air will be oxidized when silver meets, which directly affects the solderability and contact resistance of the switch. Therefore, the high quality light touch switch must be made on the pin. Silver plating thickness of base material and silver plating processing technology are well controlled in many aspects. The order of silver plating quality in the sales market is as follows: the method of switching switch operation and matters needing attention
Silver plating thickness: 0.3um or more (silver), 0.2um (thin silver), 0.1um (white)
Silver plating process: base material pre-plated nickel and silver, base material pre-plated copper and silver, base material direct silver plating
It is very important whether the protective agent treatment or the switch has the function of dust-proof and moisture-proof after silver plating on the base material. Otherwise, even if the silver plating treatment is better, the power switch will be oxidized.
Secondly, the key negative influence factor of conduction reliability is the structure of contact point. Because the function of touch switch is contact conduction between contact point and spring plate, the larger the contact surface is, the better the contact surface is. The contact surface is determined by structure. There are several kinds of structures in the sales market. The order of good and bad is as follows:
Bubble (crater type) "o contact", "grooved type" 2-point contact"and"flat bubble type"1-point contact
Thirdly, the service life and touch are determined by the cooperation between the stroke of the light touch switch and the spring blade. The less the stroke, the lighter the noise, the longer the service life. On the contrary, the service life of the light touch switch is determined by the stroke or sound under the fixed technological condition of the spring blade.
Another subjective factor determining the service life of spring blades is stamping technology. The stamping technology in Japan, China and Taiwan has been widely used in China for a long time. Therefore, under the condition of technological improvement, whether the standard for raw materials imported is reduced again, for example, the service life of 160gf spring blades in the sales market is mainly four. Species.
Fourth is the production process. After having spare parts, the final impact on quality is the assembly process. The assembly process depends on the management ability of the production enterprise, the meaning of the quality of employees and the quality assurance ability. The final product quality of different guaranteed abilities varies, of course. The assembly methods of the sales market are as follows: Manpower and equipment, equipment assembly low cost but low product quality, manual assembly cost increases but also high quality.
Fifth, factory inspection, the way and project of factory inspection also affect the quality of the final touch switch, such as appearance, touch, conduction, resistor and other items are sampling inspection or full inspection, for example, the unqualified rate of some large factory standards is considered by ppm or zero defect, it is necessary to set after the factory inspection set full inspection. Sampling inspection or quality supervision.
But the switching switch also has its shortcomings. Frequent pressing will make metal shrapnel inelastic and ineffective in fatigue. Therefore, the buttons of most electrical appliances are directly replaced by conductive rubber or pot switch hardware bullets, such as computer keyboards, remote controllers and so on. On the foot connection of five-legged lightly touching switch: two pins are in a group, four pins are for soldering more firmly, and the fifth pin is for grounding wire.